Threats
CVEs published in the last 120 days, plus everything on CISA’s known-exploited list. Scores, exploit likelihood and exploitation status in one place.
| Score | CVE | Affected | EPSS | Published |
|---|---|---|---|---|
| — unscored | CVE-2026-98191 | Linux In the Linux kernel, the following vulnerability has been resolved: wifi: wlcore: release runtime PM ref on regdomain config failure wlcore_regdomain_config() gets a runtime PM reference before sending the regulatory-domain command. When wlcore_cmd_regdomain_config_locked() fails, the function queues recovery and returns without dropping that reference. Release the reference after handling the command result so both success and failure paths balance the preceding pm_runtime_resume_and_get(). The recovery worker takes a separate runtime PM reference and cannot release the reference held here. | 0.18% | 6 Oct 2026 |
| — unscored | CVE-2026-98190 | Linux In the Linux kernel, the following vulnerability has been resolved: wifi: wilc1000: fix out-of-bounds read in P2P public action frames wilc_wfi_p2p_rx() and mgmt_tx() start parsing a frame once ieee80211_is_public_action() returns true. That helper only verifies the frame is long enough for the action category field, that is offsetofend(struct ieee80211_mgmt, u.action.category), 25 bytes. Both functions then read the P2P public action header up to oui_subtype at offset 30 and pass "size - ie_offset" to cfg80211_find_vendor_ie(), where ie_offset is offsetof(struct ieee80211_mgmt, u) + sizeof(*d), i.e. 32. A public action frame of 25 to 31 bytes passes the check but is shorter than that 32 byte header, so oui_subtype can be read out of bounds, and because the length is unsigned, "size - ie_offset" underflows to a value close to 4 GiB. cfg80211_find_vendor_ie() takes an unsigned int length, so even the size_t subtraction in mgmt_tx() is truncated to the same value. It then walks far past the buffer searching for a vendor element until it reaches unmapped memory. In the receive path the frame arrives over the air and needs no association, so a nearby unauthenticated device can crash the host while it is in P2P listen. Reject frames shorter than the P2P public action header in both paths before dereferencing it. | 0.18% | 6 Oct 2026 |
| — unscored | CVE-2026-98189 | Linux In the Linux kernel, the following vulnerability has been resolved: wifi: wilc1000: fix RX buffer OOB-write in wilc_wlan_handle_isr_ext() wilc_wlan_handle_isr_ext() takes the RX transfer size from the device-reported interrupt status register (a 15-bit field shifted left by 2, up to 131068 bytes) and reads that many bytes from the device into rx_buffer, which is only WILC_RX_BUFF_SIZE (96K) large. The wrap check only handles the current offset; the size itself is never compared against the buffer, so a bogus SDIO device can make the driver OOB-write rx_buffer by up to ~32K with data it controls. The oversized transfer also leaves rx_buffer_offset past the end of the buffer, after which the unsigned wrap check stops working and the overflow can repeat. Drop any transfer whose size exceeds the RX buffer, acknowledging the data interrupt and re-arming the RX engine so the bogus frame is discarded and reception can continue. This also restores the rx_buffer_offset <= WILC_RX_BUFF_SIZE invariant the wrap check relies on. This is not expected to change driver behavior in most cases: without this check, an oversized transfer would most likely corrupt neighboring kernel memory instead of completing anyway, and the drop path performs the same interrupt acknowledgment and RX engine re-arming as the normal path, so subsequent transfers are received unaffected. Discovered by Atuin - Automated Vulnerability Discovery Engine. | 0.18% | 6 Oct 2026 |
| — unscored | CVE-2026-98188 | Linux In the Linux kernel, the following vulnerability has been resolved: wifi: p54: validate curve data length in the calibration curve converters p54_convert_rev0() and p54_convert_rev1() read calibration curve data from the device-supplied EEPROM entry using channel and points-per-channel counts taken verbatim from that same entry, so an entry that declares more data than it carries drives an out-of-bounds read past the EEPROM buffer (verified with a KASAN reproducer of the conversion loop). The sibling converters p54_convert_output_limits() and p54_convert_db() already validate their counts against the entry length; this path was missed. Reject the entry when the counts do not fit in the entry data. | 0.22% | 6 Oct 2026 |
| — unscored | CVE-2026-98187 | Linux In the Linux kernel, the following vulnerability has been resolved: wifi: p54: require a full exp_if record in PDR_INTERFACE_LIST The PDR_INTERFACE_LIST loop only checks that the record start is within the entry before reading an entire struct exp_if from it. A truncated trailing record makes the if_id/variant reads cross the entry boundary into the heap beyond the EEPROM buffer (verified with a KASAN reproducer of the loop). The variant also feeds the synth front-end selection, so this is not only a leak. Advance only while a full record still fits in the entry. | 0.18% | 6 Oct 2026 |
| — unscored | CVE-2026-98186 | Linux In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: bound the pairwise-cipher OUI walk to the IE length mwifiex_search_oui_in_ie() reads a pairwise-cipher (PTK) count from a beacon/probe-response RSN or WPA information element and then walks that many 4-byte OUIs, comparing each with memcmp(). The count comes straight from the (attacker-supplied) IE and is never checked against the element's own length, and the callers admit the element on element_id alone (has_ieee_hdr() / has_vendor_hdr(), no length check). A crafted RSN/WPA IE with a large pairwise count therefore makes the walk read up to 255 * 4 bytes past the element -- an out-of-bounds read of the kmemdup()'d beacon buffer, reachable from any AP whose beacon/probe response is processed during scan-result parsing. Pass the number of IE bytes available at the OUI list and bound the walk to the element. Keep the length signed and reject a negative value before any unsigned arithmetic, so a small or zero IE length cannot underflow to a large size_t and defeat the bound. Found by 0sec automated security-research tooling (https://0sec.ai). | 0.18% | 6 Oct 2026 |
| — unscored | CVE-2026-98185 | Linux In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: validate scan response extents mwifiex_ret_802_11_scan() subtracts the fixed response fields and the firmware-provided BSS length from resp->size without first proving that either extent fits. A short response or oversized BSS length can therefore underflow tlv_buf_size and make the TLV parser walk beyond the command response. Compute the fixed extent from the selected normal or background scan response. Validate that the fixed fields and BSS data fit before deriving the TLV extent and entering the parser. | 0.18% | 6 Oct 2026 |
| — unscored | CVE-2026-98184 | Linux In the Linux kernel, the following vulnerability has been resolved: wifi: mwifiex: prevent authentication frame length truncation mwifiex_cfg80211_authenticate() derives the authentication frame length from req->ie_len and req->auth_data_len, both of type size_t, but stores it in a u16. NL80211_ATTR_AUTH_DATA only has a minimum length policy. Since nla_len is a u16, a single attribute can carry up to 65531 bytes of payload, so the sum can exceed U16_MAX before it is assigned to pkt_len. The truncated pkt_len determines the skb frame area, while the copy length remains req->auth_data_len - 4, resulting in a heap buffer overflow. For example, with auth_data_len equal to 65510 and no IEs, the sum is 65546. It is truncated to 10 and then reduced by four to 6. The driver appends only six bytes to the skb with skb_put(), but then copies 65506 user-provided bytes into the authentication body. Reaching this path requires CAP_NET_ADMIN in the user namespace owning the network namespace, an up station netdev, and a suitable BSS/SAE authentication request. Compute the length in size_t, reject values that cannot be represented by the firmware's u16 frame length field, and only then assign it to pkt_len. | 0.27% | 6 Oct 2026 |
| — unscored | CVE-2026-98183 | Linux In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: avoid out-of-bounds read for empty PREQ elements ieee80211_mesh_preq_size_ok() derives the location of the PREQ bottom fields before checking whether the element contains even the fixed header. ieee80211_mesh_hwmp_preq_get_bottom() reads the flags byte to account for the optional Address Extension field. Consequently, an empty PREQ element causes a one-byte read beyond its declared payload. Move the helper call after both size checks, so the bottom fields are only accessed when they are present. | 0.16% | 6 Oct 2026 |
| — unscored | CVE-2026-98182 | Linux In the Linux kernel, the following vulnerability has been resolved: wifi: mac80211: refuse to make a monitor active when it has no queue A monitor interface only gets a TXQ if it's created active, and one can't be added later. Setting the flag on a down interface is still allowed, so the driver is handed a monitor with no queue. ath9k dereferences it: BUG: kernel NULL pointer dereference, address: 0000000000000066 RIP: 0010:ath_tx_node_init+0x49/0x170 [ath9k] ath9k_add_interface+0x10c/0x140 [ath9k] drv_add_interface+0x54/0x250 [mac80211] ieee80211_do_open+0x32f/0x800 [mac80211] Reached with CAP_NET_ADMIN by "iw dev X set monitor active" followed by "ip link set X up". RTNL is held, so netlink operations block behind it. Refuse the flag when there is no queue to give. | 0.18% | 6 Oct 2026 |
| — unscored | CVE-2026-98181 | Linux In the Linux kernel, the following vulnerability has been resolved: drm/gud: fix out-of-bounds write in gud_plane_atomic_check() The plane property loop uses req->properties[num_properties + i] as write index while simultaneously incrementing `num_properties` inside the loop. At iteration i, num_properties has also incremented by i, so the write is done at `initial_num_properties + 2*i`, skipping every other index and advancing by 2 per iteration. With just 2 connector and 32 plane properties the last write happens at index 64, one slot past the end of the 64-slot (indices 0–63) allocation. A USB device can trigger OOB by advertising the maximum number of properties. Fix by dropping the redundant `+ i`; num_properties is already the correct running index, as gud_connector_fill_properties() fills the preceding slots. | 0.21% | 6 Oct 2026 |
| 7.1 high | CVE-2026-98180 | Linux In the Linux kernel, the following vulnerability has been resolved: drm/msm: RCU-free the scheduler-containing ring and VM objects Both struct msm_ringbuffer and struct msm_gem_vm embed a struct drm_gpu_scheduler. msm_ringbuffer_destroy() and the VM free callback msm_gem_vm_free() call drm_sched_fini() on the embedded scheduler and then free the containing object with plain kfree(). drm_sched_fence_get_timeline_name() returns fence->sched->name, and the scheduler fence keeps a .release callback so it is not ops-detached on signalling. A finished fence exported to userspace (the submit out-fence, or a VM_BIND fence, via sync_file / drm_syncobj) keeps pointing at the embedded scheduler after the ring/VM is freed, so a later get_timeline_name() -- reachable unprivileged through SYNC_IOC_FILE_INFO -- dereferences freed slab memory (KASAN slab-use-after-free read). Per the dma-fence lifetime contract the exporter must keep the data backing a signalled fence alive for an RCU grace period. Free the scheduler-containing objects with kfree_rcu() instead of kfree(). Patchwork: https://patchwork.freedesktop.org/patch/750234/ | 0.21% | 6 Oct 2026 |
| — unscored | CVE-2026-98179 | Linux In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: fix rmmio iounmap skipped on device removal amdgpu_pci_remove() calls drm_dev_unplug() before fini_sw(), so drm_dev_enter() is already false there and the iounmap() guarded by it is skipped. This .remove path runs on both hot-unplug and plain rmmod, so the register BAR ioremap mapping leaks one instance per unload. Unmap rmmio unconditionally (guard only on non-NULL) and drop the now unused idx. (cherry picked from commit dd6f86a97260e5207d3329ad03aa89fdad61b1e6) | 0.18% | 6 Oct 2026 |
| — unscored | CVE-2026-98178 | Linux In the Linux kernel, the following vulnerability has been resolved: drm/amdgpu: Skip KFD mapping clear before initialization amdgpu_amdkfd_clear_kfd_mapping() assumes that a non-NULL kfd_dev has a fully populated node array. This is not true when KFD device initialization fails after probe. For example, kgd2kfd_device_init() sets num_nodes before checking PCIe atomics support. On Polaris systems without the required atomics, it returns before allocating nodes[0], but the kfd_dev remains attached to the amdgpu device. A later GPU reset then dereferences nodes[0]->id. Require the authoritative KFD initialization flag before walking the node array, matching the existing KFD reset and teardown paths. (cherry picked from commit 4ac1835823c47903fbb278bbf474773c46f59edc) | 0.20% | 6 Oct 2026 |
| — unscored | CVE-2026-98177 | Linux In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Avoid integer underflow in EOP ring size calculation. The low 6 bits of cp_hqd_eop_control store the base-2 logarithm of the EOP ring size. This was calculated as order_base_2(q->eop_ring_buffer_size / 4) - 1 But order_base_2 can in theory return 0, so this could underflow (although in practice the ring buffer size cannot be less than 4096). Change this to order_base_2(q->eop_ring_buffer_size / 8) using properties of logarithms. Also add to the above comment to make the mathematics more clear. (cherry picked from commit f0f43fcf8b2b3a924cad9444340921c96ed5f634) | 0.20% | 6 Oct 2026 |
| — unscored | CVE-2026-98176 | Linux In the Linux kernel, the following vulnerability has been resolved: drm/amdkfd: Avoid integer underflow with ffs in EOP ring size calc The low 6 bits of cp_hqd_eop_control store the base-2 logarithm of the EOP ring size. This was calculated as ffs(q->eop_ring_buffer_size / sizeof(unsigned int)) - 1 - 1 But ffs can in theory return 1 or 0, so this could underflow (although in practice the ring buffer size cannot be less than 4096). Change this to ffs(q->eop_ring_buffer_size / sizeof(unsigned int) / 4) using properties of logarithms. (cherry picked from commit 4f18c56630383c14bfc6b2d65f88f2f895d2121a) | 0.16% | 6 Oct 2026 |
| 7.5 high | CVE-2026-98175 | Linux In the Linux kernel, the following vulnerability has been resolved: smb: client: cancel reconnect work in clean_demultiplex_info() clean_demultiplex_info() cancels server->echo delayed work but not server->reconnect, which can cause a use-after-free when the demultiplex thread exits while a reconnect work is still queued: cifs_demultiplex_thread() cifs_readv_from_socket() cifs_reconnect() __cifs_reconnect() cifs_queue_server_reconn() mod_delayed_work(cifsiod_wq, &server->reconnect, 0) clean_demultiplex_info() cancel_delayed_work_sync(&server->echo) // echo canceled // reconnect NOT canceled kfree_sensitive(server) // server freed ...later, on cifsiod_wq: smb2_reconnect_server() server->srv_count // UAF read of freed server Fix this by canceling server->reconnect delayed work in clean_demultiplex_info() before the server is freed, the same way cifs_put_tcp_session() already does. | 0.21% | 6 Oct 2026 |
| 7.5 high | CVE-2026-98174 | Linux In the Linux kernel, the following vulnerability has been resolved: smb: client: fix rlist race and missing initialization TCP_Server_Info.rlist is allocated via kzalloc which zeros both ->next and ->prev to NULL instead of pointing to itself, making list_empty() always return false and list_add() dereference a NULL ->prev pointer. Also, cifs_signal_cifsd_for_reconnect() can be called concurrently from multiple cifsd threads, allowing the same server's rlist node to be added twice into the local list, corrupting it. | 0.18% | 6 Oct 2026 |
| 7.5 high | CVE-2026-98173 | Linux In the Linux kernel, the following vulnerability has been resolved: smb: client: fix use-after-free of iface in cifs_try_adding_channels() cifs_try_adding_channels() iterates ses->iface_list with list_for_each_entry_safe_from(), which captures the next entry (niface) under iface_lock. The loop body then drops iface_lock for the whole duration of cifs_ses_add_channel(). A concurrent interface refresh (SMB3_request_interfaces() -> parse_server_interfaces()) marks all ifaces inactive and removes and frees any that are not re-advertised via list_del() + kref_put(), where release_iface() is a bare kfree(). Since niface typically has no channel holding a reference, the list reference is its last and it can be freed inside the unlocked window. On continue, the iterator advance step then dereferences niface->iface_head.next, and the loop body reads iface->rdma_capable/is_active, both on freed memory. Fix this by never keeping an unreferenced list pointer across the unlocked window. Each channel attempt now re-scans the list from the head under iface_lock, takes a kref on the selected candidate, and passes only that referenced candidate to cifs_ses_add_channel(). weight_fulfilled still tracks selection progress, so restarting the scan preserves the original weighted distribution and the weight_fulfilled-before-kref_put ordering on the failure path. Add a per-pass attempts cap so a flapping interface refresh cannot keep the inner loop spinning within a single tries increment. | 0.21% | 6 Oct 2026 |
| — unscored | CVE-2026-98172 | Linux In the Linux kernel, the following vulnerability has been resolved: smb: client: fix smbd_connection leak on cifs_get_tcp_session() error When an RDMA connection is successfully established via smbd_get_connection() but cifs_get_tcp_session() later fails (e.g. kthread_create() returns an error), the error path frees tcp_ses without first destroying the smbd_connection. Fix this by calling smbd_destroy() in the out_err cleanup path before kfree(tcp_ses). smbd_destroy() safely handles the case where smbd_conn is NULL, so it can be called unconditionally. | 0.21% | 6 Oct 2026 |